کاوشگر فیله ساعت ۹:۳۵ دقیقه روز چهارشنبه ۱۲ نوامبر به وقت اروپای مرکزی برای فرود بر سطح ستارهٔ دنبالهدار از حامل خود فضاپیمای رزتا در فضا رها شد، و پس از هفت ساعت کاهش ارتفاع سرانجام بر روی دنبالهدار ۶۷پی فرود آمد. فرودش بر دنبالهدار در حدود ساعت ۱۶:۰۵ گرینویچ تأیید شد. فیله موفق شد به مدت ۶۰ ساعت بر روی این جرم فضایی به پژوهش و نمونهبرداری و ارسال داده بپردازد تا اینکه باتری آن تمام شد. فرود فیله بر روی جرم فضایی با مشکلاتی روبهرو شد بهطوریکه چنگکهای اتصال آن به سطح دنبالهدار عمل نکرده و باعث شدند که این کاوشگر دو بار از جای خود کنده شده و در یک شکاف فرود بیاید که این امر باعث نرسیدن آفتاب کافی به صفحات سلول خورشیدی آن شد. فیله در ۱۴ ژوئن ۲۰۱۵ (۲۴ خرداد ۱۳۹۴) با نزدیکتر شدن دنبالهدار به خورشید و افزایش ساعتهای نورگیری، دوباره به کار افتاد. اما در تاریخ ۹ ژوئیه ۲۰۱۵ (۱۸ تیر ۱۳۹۴) بار دیگر تماس با کاوشگر فیله بار دیگر قطع شد.
دادهها نشان داد که واحد فرود به نام فیله حدود ۴ سانتیمتر در خاک سطح دنبالهدار فرورفته که نشانگر نرم بودن لایه سطحی این جرم آسمانی است. اما به فاصله کوتاهی بعد از آن مهندسان متوجه شدند که زوبینهای طراحی شده برای محکم کردن فیله روی سطح دنبالهدار به درستی عمل نکردهاست. محل فرود فیله محوطهای به ابعاد ۹۰۰ در ۶۰۰ متر است و این کاوشگر که حدود یکصد کیلوگرم وزن دارد حامل وسایل آزمایشگاهی برای اولین بررسی نزدیک سطح یک دنبالهدار است.
اما با وجود موفقیت در فرود محل دقیق استقرار فیله بر سطح دنبالهدار ۶۷ پی مشخص نیست. به ویژه اینکه پس از نخستین تماس دست کم دو بار از جای خود بلند شده و دوباره فرود آمدهاست. پس از فرود ارتباط فیله با فضاپیمای رزتا و زمین قطع شد. اما پس از مدتی نخستین تصاویر خود را به زمین ارسال کرد. سپس به علت قرار گرفتن در سایهٔ احتمالاً یک صخره، مشکل تضعیف باتریهای خورشیدی پیش آمد. دانشمندان با تغییر موقعیت کاوشگر، موقتاً موفق به حل این مسئله شدند اما مشکل همچنان باقی ماند.
فیله در شبانهروز نیاز به حداقل ۷ ساعت نور خورشید دارد ولی به علت استقرار در سایه، فقط یک ساعت و نیم در معرض نور قرار میگیرد. همین مسئله باعث توقف کارکردهای کاوشگر و به خواب رفتن آن بعد از ۵۷ ساعت در جمعه شب ۲۳ آبان شد. اما قبل از آن موفق به تشخیص مولکولهای آلی حاوی کربن در جو چوری شد که از جهت کشف اسرار پیدایش حیات در کرهٔ زمین حائز اهمیت است. دانشمندان آلمانی در حال تجزیه و تحلیل یافتههای فیله در این مورد هستند. فعالیت مجدد کاوشگر احتمالاً تا قبل از فصل بهار سال ۲۰۱۵ و با شارژ مجدد توسط پنلهای باتری خورشیدی شروع خواهد شد.
عمر چوری ۴ میلیارد سال برآورد میشود. فاصلهاش با زمین در زمان فرود کاوشگر، قریب ۵۰۰ میلیون کیلومتر بودهاست؛ از این رو حدود نیم ساعت زمان میبرد تا امواج رادیویی طول این مسیر را طی کند. این ستارهٔ دنبالهدار به زودی داغ خواهد شد و مقادیر عظیمی گاز و غبار از خود بیرون خواهد ریخت.
آندرا آکاماتزو میگوید: «ستارهٔ دنبالهدار به خورشید نزدیک میشود و به خوبی میدانیم که فعال خواهد شد. زمانی خواهد رسید که دیگر نمیتوانیم در مدار ستارهٔ دنبالهدار بمانیم. دقیقاً نمیدانیم این زمان کِی است، شاید ژانویهٔ سال آینده، شاید فوریه، شاید مارس، هنوز نمیدانیم.»
ماریو سالاتی در اینباره میگوید: «کاوشگر فیله در رأس ستارهٔ دنبالهدار قرار دارد و همانجا هم خواهد ماند. البته دنبالهدار به خورشید نزدیک میشود و شاید باتری ثانویهٔ فیله پر شود و کاوشگر دوباره به کار بیفتد»
پروژه پرتاب کاوشگر روزتا یکی از پیچیدهترین و دشوارترین طرحهای فضایی تاریخ است که ۱٫۴ میلیارد دلار هزینه داشتهاست. این پروژه از سال ۱۹۹۴ آغاز شد و در ماه مارس سال ۲۰۰۴ سفینه روزتا و کاوشگر فیله به فضا پرتاب شدند.
فیله در ۱۴ ژوئن ۲۰۱۵ (۲۴ خرداد ۱۳۹۴) با نزدیکتر شدن دنبالهدار به خورشید و افزایش ساعتهای نورگیری، دوباره به کار افتاد. فیله بکار افتادن دوباره خود را در توییتر با این پیغام اعلام کرد: "سلام زمین، صدای من را میشنوی؟" روزتا هم با توئیتی پاسخ داد: "یک خبر فوقالعاده، کاوشگر من، فیله بیدار شدهاست."
در تاریخ ۹ ژوئیه ۲۰۱۵ (۱۸ تیر ۱۳۹۴) بار دیگر تماس با کاوشگر فیله بار دیگر قطع شد. این قطع تماس احتمالاً به دلیل گازهای متصاعد شده از سطح دنبالهدار و جابجایی دوباره کاوشگر باشد که مانع از تابش نور آفتاب بر صفحات خورشیدی و مسدود شدن آنتنهای فیله شده باشد بهطوریکه یکی از فرستندههای آن از کار افتاده باشد.
فیله پیش از اینکه از کار بیفتد تصاویر و اطلاعات مربوط به محل فرود خود را مخابره کرده بود اما محل فرود آن برای دانشمندان نامعلوم باقی ماند. در تاریخ ۵ سپتامبر ۲۰۱۶ (۱۵ شهریور ۱۳۹۵) با تصاویر جدیدی که روزتا مخابره کرد این حدس دانشمند را تأیید شد که فیله زیر بر آمدگی یک صخره قرار گرفتهاست. آنها گفتند که اینکه امیدی به بازیافت کاوشگر فیله وجود ندارد و برخی از دستگاههای آن در سرما از کار افتادهاند و اینکه محل دقیق آن مشخص شده به دانشمندان در تجزیه و تحلیل بهتر اطلاعاتی که این کاوشگر ارسال کرده کمک میکند. دانشمندان قصد دارند با سقوط مدارگرد روی سطح دنبالهدار به مأموریت روزتا پایان دهند.
برترین دستاورد علمی ۲۰۱۴ از نگاه مجله ساینس[ویرایش]
فرود نرم این کاوشگر بر روی ستاره ۶۷ پی به عنوان برترین دستاورد علمی ۲۰۱۴ از سوی مجله ساینس برگزیده شد. نمایندگان مجله ساینس در بیانیهای اعلام کردند:
اگرچه فرود کاوشگر سختتر از انتظارات پیشین بود و فیله در جایی دورتر از هدفش فرود آمد، در هر صورت این نخستین فرود نرم بر روی یک دنبالهدار بهشمار میرود. دادههای این دو کاوشگر فضایی تا به این لحظه درک بهتری از شکلگیری و تکامل چنین دنبالهدارهایی ارائه کردهاست.
Despite the landing problems, the probe's instruments obtained the first images from a comet's surface. Several of the instruments on Philae made the first direct analysis of a comet, sending back data that will be analysed to determine the composition of the surface.
On 15 November 2014 Philae entered safe mode, or hibernation, after its batteries ran down due to reduced sunlight and an off-nominal spacecraft orientation at its unplanned landing site. Mission controllers hoped that additional sunlight on the solar panels might be sufficient to reboot the lander.Philae communicated sporadically with Rosetta from 13 June to 9 July 2015, but contact was then lost. The lander's location was identified to within a few tens of metres, but it was not seen. Philae, though silent, was finally identified unambiguously, lying on its side in a deep crack in the shadow of a cliff, in photographs taken by Rosetta on 2 September 2016 as the orbiter was sent on orbits closer to the comet. Knowledge of its precise location will help in interpretation of the images it had sent. On 30 September 2016, the Rosetta spacecraft ended its mission by crashing in the comet's Ma'at region.
Philae's mission was to land successfully on the surface of a comet, attach itself, and transmit data about the comet's composition. The Rosetta spacecraft and Philae lander were launched on an Ariane 5G+ rocket from French Guiana on 2 March 2004, 07:17 UTC, and travelled for 3,907 days (10.7 years) to Churyumov–Gerasimenko. Unlike the Deep Impact probe, which by design struck comet Tempel 1's nucleus on 4 July 2005, Philae is not an impactor. Some of the instruments on the lander were used for the first time as autonomous systems during the Mars flyby on 25 February 2007. CIVA, one of the camera systems, returned some images while the Rosetta instruments were powered down, while ROMAP took measurements of the Martian magnetosphere. Most of the other instruments need contact with the surface for analysis and stayed offline during the flyby. An optimistic estimate of mission length following touchdown was "four to five months".
The goals of the scientific mission have been summarized as follows:
"The scientific goals of its experiments focus on elemental, isotopic, molecular and mineralogical composition of the cometary material, the characterization of physical properties of the surface and subsurface material, the large-scale structure and the magnetic and plasma environment of the nucleus. In particular, surface and sub-surface samples will be acquired and sequentially analyzed by a suite of instruments. Measurements will be performed primarily during descent and along the first five days following touch-down."
Landing and surface operations
Depiction of Philae on Churyumov-Gerasimenko
Philae remained attached to the Rosetta spacecraft after rendezvousing with Churyumov–Gerasimenko on 6 August 2014. On 15 September 2014, ESA announced "Site J" on the smaller lobe of the comet as the lander's destination. Following an ESA public contest in October 2014, Site J was renamed Agilkia in honour of Agilkia Island.
A series of four Go/NoGo checks were performed on 11–12 November 2014. One of the final tests before detachment from Rosetta showed that the lander's cold-gas thruster was not working correctly, but the "Go" was given anyway, as it could not be repaired.Philae detached from Rosetta on 12 November 2014 at 08:35 UTC SCET.
Rosetta signal received at ESOC in Darmstadt, Germany (20 January 2014)
Philae's landing signal was received by Earth communication stations at 16:03 UTC after a 28-minute delay. Unknown to mission scientists at that time, the lander had bounced. It began performing scientific measurements while slowly moving away from the comet and coming back down, confusing the science team. Further analysis showed that it bounced twice.
Philae's first contact with the comet occurred at 15:34:04 UTC SCET. The probe rebounded off the comet's surface at 38 cm/s (15 in/s) and rose to an altitude of approximately 1 km (0.62 mi). For perspective, had the lander exceeded about 44 cm/s (17 in/s), it would have escaped the comet's gravity. After detecting the touchdown, Philae'sreaction wheel was automatically powered off, resulting in its momentum being transferred back into the lander. This caused the vehicle to begin rotating every 13 seconds. During this first bounce, at 16:20 UTC SCET, the lander is thought to have struck a surface prominence, which slowed its rotation to once every 24 seconds and sent the craft tumbling.Philae touched down a second time at 17:25:26 UTC SCET and rebounded at 3 cm/s (1.2 in/s). The lander came to a final stop on the surface at 17:31:17 UTC SCET. It sits in rough terrain, apparently in the shadow of a nearby cliff or crater wall, and is canted at an angle of around 30 degrees, but is otherwise undamaged. Its final location was determined initially by analysis of data from CONSERT in combination with the comet shape model based on images from the Rosetta orbiter, and later precisely by direct imaging from Rosetta.
An analysis of telemetry indicated that the initial impact was softer than expected, that the harpoons had not deployed, and that the thruster had not fired. The harpoon propulsion system contained 0.3 grams of nitrocellulose, which was shown by Copenhagen Suborbitals in 2013 to be unreliable in a vacuum.
Operations and communication loss
Philae's intended landing site Agilkia (Site J)
The primary battery was designed to power the instruments for about 60 hours. ESA expected that a secondary rechargeable battery would be partially filled by the solar panels attached to the outside of the lander, but the limited sunlight (90 minutes per 12.4-hour comet day) at the actual landing site was inadequate to maintain Philae's activities, at least in this phase of the comet's orbit.
On the morning of 14 November 2014, the battery charge was estimated to be only enough for continuing operations for the remainder of the day. After first obtaining data from instruments whose operation did not require mechanical movement, comprising about 80% of the planned initial science observations, both the MUPUS soil penetrator and the SD2 drill were commanded to deploy. Subsequently, MUPUS data as well as COSAC and Ptolemy data were returned. A final set of CONSERT data was also downlinked towards the end of operations. During the evening's transmission session, Philae was raised by 4 centimetres (1.6 in) and its body rotated 35 degrees to more favourably position the largest solar panel to capture the most sunlight in the future. Shortly afterwards, electrical power dwindled rapidly and all instruments were forced to shut down. The downlink rate slowed to a trickle before coming to a stop. Contact was lost on 15 November at 00:36 UTC.
Prior to falling silent, the lander was able to transmit all science data gathered during the First Science Sequence ... This machine performed magnificently under tough conditions, and we can be fully proud of the incredible scientific success Philae has delivered.
Data from the SESAME instrument determined that, rather than being "soft and fluffy" as expected, Philae's first touchdown site held a large amount of water ice under a layer of granular material about 25 cm (9.8 in) deep. It found that the mechanical strength of the ice was high and that cometary activity in that region was low. At the final landing site, the MUPUS instrument was unable to hammer very far into the comet's surface, despite power being gradually increased. This area was determined to have the consistency of solid ice or pumice.
In the atmosphere of the comet, the COSAC instrument detected the presence of molecules containing carbon and hydrogen. Soil elements could not be assessed, because the lander was unable to drill into the comet surface, likely due to hard ice. The SD2 drill went through the necessary steps to deliver a surface sample to the COSAC instrument, but nothing entered the COSAC ovens.
Upon Philae's first touchdown on the comet's surface, COSAC measured material at the bottom of the vehicle, which was disturbed by the landing, while the Ptolemy instrument measured material at the top of the vehicle. Sixteen organic compounds were detected, four of which were seen for the first time on a comet, including acetamide, acetone, methyl isocyanate and propionaldehyde.
On 13 June 2015 at 20:28 UTC, ground controllers received an 85-second transmission from Philae, forwarded by Rosetta, indicating that the lander was in good health and had sufficiently recharged its batteries to come out of safe mode.Philae sent historical data indicating that although it had been operating earlier than 13 June 2015, it had been unable to contact Rosetta before that date. The lander reported that it was operating with 24 watts of electrical power at −35 °C (−31 °F).
A new contact between Rosetta and Philae was confirmed on 19 June 2015. The first signal was received on the ground from Rosetta at 13:37 UTC, while a second signal was received at 13:54 UTC. These contacts lasted about two minutes each and delivered additional status data. By 26 June 2015, there had been a total of seven intermittent contacts between the lander and orbiter. There were two opportunities for contact between the two spacecraft each Earth day, but their duration and quality depended on the orientation of the transmitting antenna on Philae and the location of Rosetta along its trajectory around the comet. Similarly, as the comet rotated, Philae was not always in sunlight and thus not always generating enough power via its solar panels to receive and transmit signals. ESA controllers continued to try to establish a stable contact duration of at least 50 minutes.
Had Philae landed at the planned site of Agilkia in November 2014, its mission would probably have ended in March 2015 due to the higher temperatures of that location as solar heating increased. As of June 2015[update], Philae's key remaining experiment was to drill into the comet's surface to determine its chemical composition. Ground controllers sent commands to power up the CONSERT radar instrument on 5 July 2015, but received no immediate response from the lander. Confirmation was eventually received on 9 July, when the lander transmitted measurement data from the instrument.
Immediately after its reawakening, housekeeping data suggested that the lander's systems were healthy, and mission control uploaded commands for Rosetta to establish a new orbit and nadir so as to optimize communications, diagnostics, and enable new science investigations with Philae. However, controllers had difficulties establishing a stable communications connection with the lander. The situation was not helped by the need to keep Rosetta at a greater and safer distance from the comet as it became more active. The last communication was on 9 July 2015, and mission controllers were unable to instruct Philae to carry out new investigations. Subsequently, Philae failed to respond to further commands, and by January 2016, controllers acknowledged no further communications were likely.
On 27 July 2016, at 09:00 UTC, ESA switched off the Electrical Support System Processor Unit (ESS) onboard Rosetta, making further communications with Philae impossible.
The lander was located on 2 September 2016 by the narrow-angle camera aboard Rosetta as it was slowly making its descent to the comet. The search for the lander had been on-going during the Rosetta mission, using telemetry data and comparison of pictures taken before and after the lander's touchdown, looking for signs of the lander's specific reflectivity.
The search area was narrowed down to the most promising candidate, which was confirmed by a picture taken at a distance of 2.7 km (1.7 mi), clearly showing the lander. The lander sits on its side wedged into a dark crevice of the comet, explaining the lack of electrical power and proper communication with the probe. Knowing its exact location provides information needed to put Philae's two days of science into proper context.
Rosetta and Philae
The lander was designed to deploy from the main spacecraft body and descend from an orbit of 22.5 kilometres (14 mi) along a ballistic trajectory. It would touch down on the comet's surface at a velocity of around 1 metre per second (3.6 km/h; 2.2 mph). The legs were designed to dampen the initial impact to avoid bouncing as the comet's escape velocity is only around 1 m/s (3.6 km/h; 2.2 mph), and the impact energy was intended to drive ice screws into the surface.Philae was to then fire a harpoon into the surface at 70 m/s (250 km/h; 160 mph) to anchor itself. A thruster on top of Philae was to have fired to lessen the bounce upon impact and to reduce the recoil from harpoon firing. During the landing, the harpoons did not fire and the thruster failed to operate, leading to a multiple-contact landing.
Communications with Earth used the Rosetta orbiter as a relay station to reduce the electrical power needed. The mission duration on the surface was planned to be at least one week, but an extended mission lasting months was considered possible.
The main structure of the lander is made from carbon fiber, shaped into a plate maintaining mechanical stability, a platform for the science instruments, and a hexagonal "sandwich" to connect all the parts. The total mass is about 100 kilograms (220 lb). Its exterior is covered with solar cells for power generation.
The Rosetta mission was originally planned to rendezvous with the comet 46P/Wirtanen. A failure in a previous Ariane 5 launch vehicle closed the launch window to reach the comet with the same rocket. It resulted in a change in target to the comet 67P/Churyumov–Gerasimenko. The larger mass of Churyumov–Gerasimenko and the resulting increased impact velocity required that the landing gear of the lander be strengthened.
Philae's power management was planned for two phases. In the first phase, the lander operated solely on battery power. In the second phase, it was to run on backup batteries recharged by solar cells.
The power subsystem comprises two batteries: a non-rechargeable primary 1000 watt-hour battery to provide power for the first 60 hours and a secondary 140 watt-hour battery recharged by the solar panels to be used after the primary is exhausted. The solar panels cover 2.2 square metres (24 sq ft) and were designed to deliver up to 32 watts at a distance of 3 AU from the Sun.
The science payload of the lander consists of ten instruments totalling 26.7 kilograms (59 lb), making up just over one quarter of the mass of the lander.
The Alpha Particle X-ray Spectrometer detects alpha particles and X-rays, which provide information on the elemental composition of the comet's surface. The instrument is an improved version of the APXS on the Mars Pathfinder.
The Comet Nucleus Infrared and Visible Analyser (sometimes given as ÇIVA) is a group of seven identical cameras used to take panoramic pictures of the surface plus a visible-light microscope and an infrared spectrometer. The panoramic cameras (CIVA-P) are arranged on the sides of the lander at 60° intervals: five mono imagers and two others making up a stereo imager. Each camera has a 1024×1024 pixel CCD detector. The microscope and spectrometer (CIVA-M) are mounted on the base of the lander, and are used to analyse the composition, texture and albedo (reflectivity) of samples collected from the surface.
The COmet Nucleus Sounding Experiment by Radiowave Transmission used electromagnetic wave propagation to determine the comet's internal structure. A radar on Rosetta transmitted a signal through the nucleus to be received by a detector on Philae.
The COmetary SAmpling and Composition instrument is a combined gas chromatograph and time-of-flight mass spectrometer to perform analysis of soil samples and determine the content of volatile components.
The MUlti-PUrpose Sensors for Surface and Sub-Surface Science instrument measured the density, thermal and mechanical properties of the comet's surface.
The Rosetta Lander Imaging System is a CCD camera used to obtain high-resolution images during descent and stereo panoramic images of areas sampled by other instruments. The CCD detector consists of 1024×1024 pixels.
The Rosetta Lander Magnetometer and Plasma Monitor is a magnetometer and plasma sensor to study the nucleus' magnetic field and its interactions with the solar wind.
The Sampling, Drilling and Distribution system obtains soil samples from the comet and transfers them to the Ptolemy, COSAC, and CIVA instruments for in-situ analysis. SD2 contains four primary subsystems: drill, ovens, carousel, and volume checker. The drill system, made of steel and titanium, is capable of drilling to a depth of 230 mm (9.1 in), deploying a probe to collect samples, and delivering samples to the ovens. There are a total of 26 platinum ovens to heat samples—10 medium temperature ovens at 180 °C (356 °F) and 16 high temperature ovens at 800 °C (1,470 °F)—and one oven to clear the drill bit for reuse. The ovens are mounted on a rotating carousel that delivers the active oven to the appropriate instrument. The electromechanical volume checker determines how much material was deposited into an oven, and may be used to evenly distribute material on CIVA's optical windows. Development of SD2 was led by the Italian Space Agency with contributions by prime contractor Tecnospazio S.p.A (now Selex ES S.p.A.) in charge of the system design and overall integration; the Italian company Tecnomare S.p.A., owned by Eni S.p.A., in charge of the design, development, and testing of the drilling/sampling tool and the volume checker; Media Lario; and Dallara. The instrument's principal investigator is Amalia Ercoli-Finzi (Politecnico di Milano).
The Surface Electric Sounding and Acoustic Monitoring Experiments used three instruments to measure properties of the comet's outer layers. The Cometary Acoustic Sounding Surface Experiment (CASSE) measures the way in which sound travels through the surface. The Permittivity Probe (PP) investigates its electrical characteristics, and the Dust Impact Monitor (DIM) measures dust falling back to the surface.
Two Canadian companies played a role in the mission. SED Systems, located on the University of Saskatchewan campus in Saskatoon, built three ground stations that were used to communicate with the Rosetta spacecraft. ADGA-RHEA Group of Ottawa provided MOIS (Manufacturing and Operating Information Systems) software which supported the procedures and command sequences operations software.
The French Space Agency, together with some scientific laboratories (IAS, SA, LPG, LISA) provided the system's overall engineering, radiocommunications, battery assembly, CONSERT, CIVA and the ground segment (overall engineering and development/operation of the Scientific Operation & Navigation Centre).
The German Space Agency (DLR) has provided the structure, thermal subsystem, flywheel, the Active Descent System (procured by DLR but made in Switzerland), ROLIS, downward-looking camera, SESAME, acoustic sounding and seismic instrument for Philae. It has also managed the project and did the level product assurance. The University of Münster built MUPUS (it was designed and built in Space Research Centre of Polish Academy of Sciences ) and the Braunschweig University of Technology the ROMAP instrument. The Max Planck Institute for Solar System Research made the payload engineering, eject mechanism, landing gear, anchoring harpoon, central computer, COSAC, APXS and other subsystems.
The Command and Data Management Subsystem (CDMS) designed in the Wigner Research Centre for Physics of the Hungarian Academy of Sciences jointly with the Space and Ground Facilities Ltd. (a spin-off company of the Wigner Research Centre for Physics). The Power Subsystem (PSS) designed in the Department of Broadband Infocommunications and Electromagnetic Theory at Budapest University of Technology and Economics. CDMS is the fault tolerant central computer of the lander, while PSS assures that the power coming from the batteries and solar arrays are properly handled, controls battery charging and manages the onboard power distribution.
Captec Ltd., based in Malahide, provided the independent validation of mission critical software (independent software validation facility or SVF) and developed the software for the communications interface between the orbiter and the lander. Captec also provided engineering support to the prime contractor for the launch activities at Kourou. Space Technology Ireland Ltd. at Maynooth University has designed, constructed and tested the Electrical Support System Processor Unit (ESS) for the Rosetta mission. ESS stores, transmits and provides decoding for the command streams passing from the spacecraft to the lander and handles the data streams coming back from the scientific experiments on the lander to the spacecraft.
The Italian Space Agency (ASI) developed the SD2 instrument and the photovoltaic assembly. Italian Alenia Space was involved in the assembly, integration and testing of the probe, as well as several mechanical and electrical ground support equipment. The company also built the probe's S-band and X-band digital transponder, used for communications with Earth.
Moog Bradford (Heerle, The Netherlands) provided the Active Descent System, which guided and propelled the lander down to its landing zone. To accomplish the ADS, a strategic industrial team was formed with Bleuler-Baumer Mechanik in Switzerland.
The GMV Spanish division has been responsible for the maintenance of the calculation tools to calculate the criteria of lighting and visibility necessary to decide the point of landing on the comet, as well as the possible trajectories of decline of the Philae module. Other important Spanish companies or educational institutions that have been contributed are as follows: INTA, Airbus Defence and Space Spanish division, other small companies also participated in subcontracted packages in structural mechanics and thermal control like AASpace (former Space Contact), and the Universidad Politécnica de Madrid.
The landing was featured heavily in social media, with the lander having an official Twitter account portraying a personification of the spacecraft. The hashtag "#CometLanding" gained widespread traction. A Livestream of the control centres was set up, as were multiple official and unofficial events around the world to follow Philae's landing on Churyumov–Gerasimenko. Various instruments on Philae were given their own Twitter accounts to announce news and science results.
Vangelis composed the music for the trio of music videos released by ESA to celebrate the first-ever attempted soft landing on a comet by ESA's Rosetta mission.
On 12 November 2014, the search engine Google featured a Google Doodle of Philae on its home page. On 31 December 2014, Google featured Philae again as part of its New Year's Eve 2014 Doodle.
^"ÇIVA". European Space Agency. Retrieved 26 August 2014.
^Kofman, W.; Herique, A.; Goutail, J.-P.; Hagfors, T.; Williams, I. P.; et al. (February 2007). "The Comet Nucleus Sounding Experiment by Radiowave Transmission (CONSERT): A Short Description of the Instrument and of the Commissioning Stages". Space Science Reviews. 128 (1–4): 413–432. Bibcode:2007SSRv..128..413K. doi:10.1007/s11214-006-9034-9.
^"CONCERT". European Space Agency. Retrieved 26 August 2014.
^"COSAC". European Space Agency. Retrieved 26 August 2014.
^"MUPUS". European Space Agency. Retrieved 26 August 2014.
^Wright, I. P.; Barber, S. J.; Morgan, G. H.; Morse, A. D.; Sheridan, S.; et al. (February 2007). "Ptolemy: An Instrument to Measure Stable Isotopic Ratios of Key Volatiles on a Cometary Nucleus". Space Science Reviews. 128 (1–4): 363–381. Bibcode:2007SSRv..128..363W. doi:10.1007/s11214-006-9001-5.
^ abMarchesi, M.; Campaci, R.; Magnani, P.; Mugnuolo, R.; Nista, A.; et al. (2001). Comet sample acquisition for ROSETTA lander mission. 9th European Space Mechanisms and Tribology Symposium. 19–21 September 2001. Liège, Belgium. Bibcode:2001ESASP.480...91M.
^Seidensticker, K. J.; Möhlmann, D.; Apathy, I.; Schmidt, W.; Thiel, K.; et al. (February 2007). "Sesame – An Experiment of the Rosetta Lander Philae: Objectives and General Design". Space Science Reviews. 128 (1–4): 301–337. Bibcode:2007SSRv..128..301S. doi:10.1007/s11214-006-9118-6.
^"Rosetta" (in German). Institut für Weltraumforschung. 8 June 2014. Retrieved 1 December 2014.
Payloads are separated by bullets ( · ), launches by pipes ( | ). Manned flights are indicated in bold text. Uncatalogued launch failures are listed in italics. Payloads deployed from other spacecraft are denoted in brackets.